How To Put Doors On Bookcase

A compact cabinet offers just enough storage to tuck away essentials in a family room, bathroom, or bedroom. Just if you lot have a express budget for this handy piece, you won't detect many design options out there. Then nosotros turned to TOH general contractor Tom Silva for some DIY advice. He demonstrated how to attach off-the-shelf stock-still-louver shutters to an cheap, set up-to-gather bookcase to make a charming chiffonier that's piece of cake on the wallet. With a few finishing touches, similar trim and bun feet, this piece volition spiff up any room you put it in, and it takes just a few hours to build. Read on to larn how.

Download the cutting list to build a cabinet from a bookshelf and shutters.

Step 1

Overview for Making a Cabinet from a Bookshelf and Shutters

The shutters are mounted to the confront of the bookcase. Choose a pair that'southward the same superlative as the bookcase, or add a header lath to make up for the difference. The superlative and base of operations are cut to the width of the bookcase, and extend past the front to cover the edges of the shutter doors and exit a reveal.

Cut LIST

You can use the cut list below or download the cut list to build a chiffonier from a bookshelf and shutters.

Bookcase. Choose a small bookcase with adjustable shelves. (Ours was 29⅝"W by 11⅝"D by 31⅝"H.) The toekick, if it has one, volition be covered by the shutter doors.

Shutters for doors. Choose shutters sized to the height and width of the bookcase. (Ours were by 14¾"W by 29"H.) If the shutters are shorter than the bookcase, add a header board at the elevation of the bookcase to brand up the gap in meridian. Once installed, the shutters should be flush with the sides of the bookcase, with a gap of almost ⅛ inch between them.

1x utility shelving. You'll rip the top and bottom of the chiffonier from this lath. The length of each piece will equal the width of the bookcase; the width of each piece will equal the depth of the bookcase plus the thickness of the shutters, plus ¼ inch for a reveal. To brand sure you take enough material, go a piece that's at least twice as long as the bookcase is wide, and wide plenty to cover the depth of the bookcase plus the thickness of the shutters and reveal.

1x3 to create a header, if necessary, and a stop cake for attaching the magnetic door catches. Go a piece long enough to span the width of the bookcase, plus several inches for the stop block.

¾-inch trim. Get enough to cover the front and side edges of the top and bottom of the cabinet.

Step ii

Build the Bookcase

Put together a ready-to-gather bookcase using the included hardware; y'all tin observe one at whatever home shop. Attach the backing, using the included nails, to go on the slice foursquare. Set the shelves aside for Step 9.

Pace 3

Attach the Peak and Base of operations

Cut two boards from 1 shelving to the width of the bookcase and to its depth plus the thickness of the shutters, plus ¼ inch for a reveal. Nail the boards to the top and bottom of the bookcase, affluent with the back and sides.

Step 4

Add together the Header

Cutting a length of 1x3 to the width of the cabinet. Lay it on the face of the cabinet and butt information technology confronting the superlative. Nail through the header and into the sides of the cabinet.

Step 5

Install the Furniture Feet

Screw the corner foot plates to the base of the cabinet virtually one½ inches in from each corner. Spiral the bun feet into the plates.

Step 6

Cutting and Secure the Trim

Miter ¾-inch molding to wrap the front end and side edges of the cabinet's superlative and base. Nail on the trim and so that it'southward flush with the chiffonier'southward top, and exercise the same for the base of operations, reversing the profile.

Step 7

Hang the Shutter Doors

Lay the shutters on the face of the cabinet. Screw ii H-hinges to the outside edge of each door and to the sides of the cabinet, using the included fasteners.

Step eight

Add together the Door Catches

Attach the metal plates to the inside top corners of the doors. Smash a stop block to the back side of the header so that the two pieces course an "L." Screw the catches to the block so that they make contact with the plates when the doors are airtight.

Step ix

Install the Knobs

Mark the knob positions on the inner stiles of the doors. Drill holes and secure the knobs with the included screws. Put in the shelves. Crude upwards the slice with sandpaper, then glaze information technology with a primer-sealer, such equally Kilz, followed past satin or semigloss paint.

Source: https://www.thisoldhouse.com/furniture/21016458/how-to-build-a-cabinet-from-a-bookshelf-and-shutters